View PI74LPT240C_1296013.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

21098765432121098765432109876543210987654321210987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 21098765432121098765432109876543210987654321210987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 21098765432121098765432109876543210987654321210987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321
PI74LPT240 Fast CMOS 3.3V 8-Bit Inverting Buffer Line Driver
PI74LPT240
Fast CMOS 3.3V 8-Bit Inverting Buffer/Line Driver
Product Features
Compatible with LCX and LVT families of products Supports 5V Tolerant Mixed-Signal Mode Operation Input can be 3V or 5V Output can be 3V or connected to 5V bus Advanced Low-Power CMOS Operation Excellent output drive capability: Balanced drives (24mA sink and source) Low ground bounce outputs Hysteresis on all inputs Industrial operating temperature range: 40C to +85C Packages available: 20-pin 173 mil wide plastic TSSOP (L) 20-pin 150 mil wide plastic QSOP (Q) 20-pin 150 mil wide plastic TQSOP (R) 20-pin 300 mil wide plastic SOIC (S)
Product Description
Pericom Semiconductors PI74LPT series of logic circuits are produced using the Companys advanced 0.6 micron CMOS technology, achieving industry leading speed grades. The PI74LPT240 is an 8-bit inverting buffer/line driver designed for driving high-capacitive memory loads. With its balanced-drive characteristics, this high-speed, low-power device provides lower ground bounce, transmission line matching of signals, fewer line reflections and lower EMI and RFI effects. This makes it ideal for driving on-board buses and transmission lines. The PI74LPT240Can be driven from either 3.3V or 5.0V devices allowing this device to be used as a translator in a mixed 3.3/5.0V system.
Logic Block Diagram
Product Pin Configuration
OEA
Product Pin Description
Pin Name OEA, OEB Dxx Oxx GND VCC Description 3-State Output Enable Inputs (Active LOW) Inputs Outputs Ground Power
OEA OEB DA0
DA0 OB0 DA1 OB1
OA0
DA2 OB2
OB0
DB0 OA1
DA3 OB3
DA1 OB1
GND
1 20 2 19 3 18 4 17 20-Pin 5 16 L,Q 6 R,S 15 7 14 8 13 9 12 10 11
VCC OEB OA0 DB0 OA1 DB1 OA2 DB2 OA3 DB3
DB1 OA2
DA2 OB2
Truth Table(1)
OEA L L H Inputs OEB L L H DXX L H X Outputs OXX H L Z
DB2 OA3
DA3 OB3
DB3
Note: 1. H = High Voltage Level, X = Don't Care, L = Low Voltage Level, Z = High Impedance
1
PS8476
04/26/00
21098765432121098765432109876543210987654321210987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321
PI74LPT240 Fast CMOS 3.3V 8-Bit Inverting Buffer Line Driver
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ................................................................ 65C to +150C Ambient Temperature with Power Applied ................................40C to +85C Supply Voltage to Ground Potential (Inputs & Vcc Only) .......... 0.5V to +7.0V Supply Voltage to Ground Potential (Outputs & D/O Only) ....... 0.5V to +7.0V DC Input Voltage ........................................................................ 0.5V to +7.0V DC Output Current ................................................................................. 120 mA Power Dissipation ......................................................................................1.0W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
DC Electrical Characteristics (Over the Operating Range, TA = 40C to +85C, VCC = 2.7V to 3.6V)
Parameters VIH VIL IIH IIL IOZH IOZL VIK IODH IODL VOH Description Input HIGH Voltage (Input pins) Input HIGH Voltage (I/O pins) Input LOW Voltage (Input and I/O pins) Input HIGH Current (Input pins) Input HIGH Current (I/O pins) Input LOW Current (Input pins) Input LOW Current (I/O pins) High Impedance Output Current (3-State Output pins) Clamp Diode Voltage Output HIGH Current Output LOW Current Output HIGH Voltage Test Conditions(1) Guaranteed Logic HIGH Level Guaranteed Logic LOW Level VCC = Max. VIN = 5.5V VCC = Max. VIN = VCC VCC = Max. VIN = GND VCC = Max. VIN = GND VCC = Max. VOUT = 5.5V VCC = Max. VOUT = GND VCC = Min., IIN = 18 mA VCC = 3.3V, VIN = VIH or VIL, VO = 1.5V(3) VCC = 3.3V, VIN = VIH or VIL, VO = 1.5V(3) VCC = Min. IOH = 0.1 mA VIN = VIH or VIL IOH = 3 mA VCC = 3.0V, IOH = 8 mA VIN = VIH or VIL IOH = 24 mA VCC = Min. IOL = 0.1 mA VIN = VIH or VIL IOL = 16 mA IOL = 24 mA VCC = Max.(3), VOUT = GND 60 VCC = 0V, VIN or VOUT 4.5V Min. 2.2 2.0 0.5 36 50 Vcc-0.2 2.4 2.4(5) 2.0 85 Typ(2) 0.7 60 90 3.0 3.0 0.2 0.3 240 150 Max. 5.5 5.5 0.8 1 1 1 1 1 1 1.2 110 200 0.2 0.4 0.5 mA 100 Units V V V A A A A A A V mA mA V V V V V V A m V
VOL
Output LOW Voltage
IOS IOFF VH
Short Circuit Current(4) Power Down Disable Input Hysteresis
Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at Vcc = 3.3V, +25C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. This parameter is guaranteed but not tested. 5. VOH = VCC 0.6V at rated current.
Capacitance (TA = 25C, f = 1 MHz)
Parameters(1) CIN COUT Description Input Capacitance Output Capacitance Test Conditions VIN = 0V VOUT = 0V Typ 4.5 5.5 Max. 6 8 Units pF pF
Note: 1. This parameter is determined by device characterization but is not production tested.
2
PS8476
04/26/00
21098765432121098765432109876543210987654321210987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321
PI74LPT240 Fast CMOS 3.3V 8-Bit Inverting Buffer Line Driver
Power Supply Characteristics
Parameters Description ICC I CC I CCD Quiescent Power Supply Current Quiescent Power Supply Current TTL Inputs HIGH Dynamic Power Supply(4)
Test Conditions(1) VCC = Max. VCC = Max. VCC = Max., Outputs Open OEX = GND One Bit Toggling 50% Duty Cycle VCC = Max., Outputs Open fI = 10 MHZ 50% Duty Cycle OEX = GND One Bit Toggling VCC = Max., Outputs Open fI = 2.5 MHZ 50% Duty Cycle OEX = GND 8 Bits Toggling VIN = GND or VCC VIN = VCC 0.6V VIN = VCC VIN = GND
(3)
Min.
Typ(2) 0.1 2.0 50
Max. 10 30 75
Units A A A/ MHz
1 2 3 4 5
IC
Total Power Supply Current(6)
VIN = VCC 0.6V VIN = GND
0.6
2.3
mA
VIN = VCC 0.6V VIN = GND
2.1
4.7(5)
6 7 8 9 10 11 12 13 14 15
Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at VCC = 3.3V, +25C ambient. 3. Per TTL driven input; all other inputs at VCC or GND. 4. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations. 5. Values for these conditions are examples of the Icc formula. These limits are guaranteed but not tested. 6. IC =IQUIESCENT + IINPUTS + IDYNAMIC IC = ICC + ICC DHNT + ICCD (fCP/2 + fINI) ICC = Quiescent Current (ICCL, ICCH and ICCZ) ICC = Power Supply Current for a TTL High Input DH = Duty Cycle for TTL Inputs High NT = Number of TTL Inputs at DH ICCD = Dynamic Current Caused by an Input Transition Pair (HLH or LHL) fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices) NCP = Number of Clock Inputs at fCP fI = Input Frequency NI = Number of Inputs at fI All currents are in milliamps and all frequencies are in megahertz.
3
PS8476
04/26/00
21098765432121098765432109876543210987654321210987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321
PI74LPT240 Fast CMOS 3.3V 8-Bit Inverting Buffer Line Driver
Switching Characteristics over Operating Range(1)
LPT240 Com. Parameters t PLH t PHL t PZH t PZL t PHZ t PLZ tSK(o) Description Propagation Delay DXX to OXX Output Enable Time OEx to Oxx Output Disable Time(4) OEx to Oxx Output Skew(5) Conditions(2) CL = 50pF RL = 500 Min.(3) 1.5 1.5 1.5 Max. 6.5 8.0 7.0 0.5 1.5 1.5 1.5 LPT240A Com. Min.(3) Max. 4.8 6.2 5.6 0.5 LPT240C Com. Min.(3) 1.5 1.5 1.5 Max. 4.3 5.8 5.2 0.5 Units ns ns ns ns
Notes: 1. Propagation Delays and Enable/Disable times are with VCC = 3.3V 0.3V, normal range. For VCC = 2.7V, extended range, all Propagation Delays and Enable/Disable times should be degraded by 20%. 2. See test circuit and waveforms. 3. Minimum limits are guaranteed but not tested on Propagation Delays. 4. This parameter is guaranteed but not production tested. 5. Skew between any two outputs, of the same package, switching in the same direction. This parameter is guaranteed by design.
Pericom Semiconductor Corporation 2380 Bering Drive * San Jose, CA 95131 * 1-800-435-2336 * Fax (408) 435-1100 * http://www.pericom.com
4
PS8476 04/26/00

▲Up To Search▲

Price & Availability of PI74LPT240C

	To Download PI74LPT240C Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .